LM 92
SNIS110D MARCH 2000REVISED MARCH 2013
www.ti.com
Digital DC Characteristics (continued)
Unless otherwise noted, these specifications apply for +V
S
= +2.7V to +5.5V for LM92CIM . Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
; all other limits T
A
= T
J
= +25 癈, unless otherwise noted.
Typical
(1)
Limits
(2)
Unit
Symbol
Parameter
Conditions
(Limit)
T_CRIT_A Output Saturation Voltage I
OUT
= 4.0 mA
0.8
V (max)
(3)
T_CRIT_A Delay
1
Conversions
(max)
t
OF
Output Fall Time
C
L
= 400 pF
250
ns (max)
I
O
= 3 mA
(3) For best accuracy, minimize output loading. 10k pull-ups resistors should be sufficient. Higher sink currents can affect sensor accuracy
with internal heating. This can cause an error of 0.64 癈 at full rated sink current and saturation voltage based on junction-to-ambient
thermal resistance.
Serial Bus Digital Switching Characteristics
Unless otherwise noted, these specifications apply for +V
S
= +2.7V to +5.5V for LM92CIM . Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
; all other limits T
A
= T
J
= +25 癈, unless otherwise noted. CL (load capacitance) on output lines = 80 pF unless
otherwise specified. Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
; all other limits T
A
= T
J
= +25 癈, unless otherwise noted.
Typical
(1)
Limits
(2) (3)
Unit
Symbol
Parameter
Conditions
(Limit)
t
1
SCL (Clock) Period
2.5
祍(min)
1
ms(max)
t
2
Data in Set-Up Time to SCL High
100
ns(min)
t
3
Data Out Stable after SCL Low
0
ns(min)
t
4
SDA Low Set-Up Time to SCL Low (Start Condition)
100
ns(min)
t
5
SDA High Hold Time after SCL High (Stop Condition)
100
ns(min)
t
TIMEOUT
SDA and SCL Time Low for Reset of Serial Interface
(4)
75
ms (min)
300
ms (max)
(1) Typical values are at T
A
= 25 癈 and represent most likely parametric norm.
(2) Limits are guaranteed to TI's AOQL (Average Outgoing Quality Level).
(3) Timing specifications are tested at the bus input logic levels (Vin(0)=0.3xVA for a falling edge and Vin(1)=0.7xVA for a rising edge) when
the SCL and SDA edge rates are similar.
(4) Holding the SDA and/or SCL lines Low for a time interval greater than t
TIMEOUT
will cause the LM92 to reset SCL and SDA to the IDLE
state of the serial bus communication (SDA and SCL set High).
Figure 4. Serial Bus Communication
6
Submit Documentation Feedback
Copyright ?20002013, Texas Instruments Incorporated
Product Folder Links: LM92
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LT1123CST#TRPBF
IC REG CTRLR SGL 5V SOT223
LT1248IS#PBF
IC PFC CTRLR AVERAGE CURR 16SOIC
LT1249IS8#PBF
IC PFC CTRLR AVERAGE CURR 8SOIC
LT1577CS-3.3/2.8#TRPBF
IC REG CTRLR DUAL OUT 16SOIC
LT1640HIN8#PBF
IC CONTRLR HOTSWAP NEGVOLT 8-DIP
LT1641IS8#TR
IC CTRLR HOTSWAP POS VOLT 8SOIC
LT1939IDD#TRPBF
IC REG DL BUCK/LINEAR 12DFN
LT3092MPST#TRPBF
IC PROG CURRENT SOURCE SOT223-3
相关代理商/技术参数
LM92CIMXNOPB
制造商:National Semiconductor 功能描述:Temp Sensor Digital Serial (2-Wire) 8-Pin SOIC N T/R
LM93
制造商:NSC 制造商全称:National Semiconductor 功能描述:Hardware Monitor with Integrated Fan Control for Server Management
LM93-1001
制造商:FLOWLINE 功能描述:Two Indicator, Windowed, 1/8 DIN, PC (13.9"h x 8.5"w x 6.7"d)
LM936-SWH
功能描述:基本/快动开关 Foot Switch
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
LM936-SWHBM
功能描述:基本/快动开关 Foot Switch
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
LM936-SWHC4
功能描述:基本/快动开关 Foot Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
LM936-SWHMB
功能描述:基本/快动开关 Foot Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
LM936-SWHO
功能描述:基本/快动开关 Foot Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel